Grobet & Valtitan Swiss Round Files
All Files are double cut (cross cut) unless otherwise noted

Back to wpe7.jpg (1231 bytes) Files Gateway Page

Round Tapered- Gradually tapered and workable to the point. Cut over the entire surface. Used where it is necessary to enlarge a hole or round off a radius. Cuts 00 & 0 have blunt ends. Cuts 1,2 & 4 have pointed ends.  
Cross Section Length Diameter Cut 00 Price Cut 0 Price Cut 1 Price Cut 2 Price Cut 4 Price Cut 6 Price
3" 3/32" . . 31.275 $12.95 31.276 $13.50 31.277 $14.60 . . .  
4" 5/32" 31.279 $11.15 31.280 $11.75 31.281 $13.85 31.282 $14.40 31.283 $16.75 .  
5" 13/64" . . . . . . 31.286 $15.70 . . .  
6" ¼" 31.287 $13.10 31.288 $13.75 31.289 $16.40 31.290 $16.85 31.292 $17.95 31.293 $19.75
8" 5/16" 31.294 $18.10 31.295 $19.00 31.296 $22.50 31.297 $23.20 31.298 $27.15 . .
10" 13/32" 31.299 $23.95 31.300 $25.40 . . 31.302 $31.95 . . . .

 

Valtitan Round Tapered Files- For platinum, stainless steel, exotic plastics and other hard to file materials.  The hardest surface known- Rockwell hardness 72HRc.  Best performance on hard-to-file surfaces. Cut 0 has blunt end.  Cut 2 has pointed end.

 Little or no clogging, a simple knock is enough to remove the chips.  Highly resistant to corrosion.  Swiss.
Length Diameter Cut 0 Price Cut 2 Price
6" ¼" 30.251V $22.50 30.252V $24.80
8" 5/16" 30.254V $30.10 30.255V $34.10

 

American Pattern Round- Used to enlarge holes and round out corners. This double cut file tapers to a point making it adaptable to a variety of hole sizes. Swiss made.
Cross Section Length Diameter Bastard Cut (00) Price per Dz. 2nd Cut (0) Price per Dz. Smooth Cut (2) Price per Dz.
4" 5/32" 32.395S $69.99 32.402S $76.99 32.408S $82.99
6" 7/32" 32.396S $46.99 32.403S $80.99 32.409S $85.99
8" 5/16" 32.397S $79.99 32.404S $91.99 32.410S $100.99
10" 3/8" 32.398S $100.99 32.405S $116.99 32.411S $136.99
12" ½" 32.399S $135.99 32.406S $151.99 32.412S $175.99
14" 5/8" 32.400S $197.99 . . . .

 

Die Sinkers' Round- Overall length 5½". Length of cut 3½".
Cut 0 Price Cut 2 Price
31.436 $20.30 31.437 $20.30

 

Habilis Round Files- For the "in-between" jobs- bigger than a needle file but smaller than a standard file. Length of cut is 4" with an overall length of 8½".
Width Cut 00 Price Cut 1 Price
1/4" 33.824 $10.20 33.827 $10.20

 

Round Needle Files 

Knurled Handles

.

Plastic Handles
Length Cut 0 Price Cut 2 Price Cut 4 Price Cut 6 Price Length Cut 0 Price Cut 2 Price Cut 4 Price
10 cm. 31.582 $10.95 31.583 $10.95 31.584 $13.15 . . 10 cm. 30.582 $12.35 30.583 $12.35 . .
14 cm. 31.585 $8.95 31.586 $9.00 31.588 $9.50 . . 14 cm. 30.585 $10.25 30.586 $10.40 30.588 $10.90
16 cm. 31.591 $9.35 31.593 $9.35 31.595 $10.25 31.596 $12.85 16 cm. 30.591 $10.70 30.593 $10.70 30.595 $11.65
20 cm. 31.597 $11.25 31.598 $11.25 31.599 $12.65 . . . . . . . . .

 

Valtitan Round Needle Files- For platinum, stainless steel, exotic plastics and other hard to file materials.  The hardest surface known- Rockwell hardness 72HRc.  Best performance on hard-to-file surfaces.  Little or no clogging, a simple knock is enough to remove the chips.  Highly resistant to corrosion.  Swiss.

Length Diameter Cut 0 Price Cut 2 Price
16 cm 5/16" 30.119V $16.20 30.120V $16.20

 

Single Cut Round Needle Files- Single cut files, in addition to being much more economical than the standard double cut,  have an advantage that they do not clog as easily as double cut files.

Length Cut 4 (fine) Price
14 cm. 33.863 $5.05

 

Economy Round Needle Files- Well made, yet economical , Swiss needle files, made of chrome alloy steel.  Cut portion is 3" long.

Length Medium Price per Dz. Fine Price per Dz.
14 cm. 33.894 $42.20 33.895 $46.75

 

Round Escapement Files- Also known as square handled needle files, these precision files have a length of cut of about 2".

Length Cut 0 Price Cut 2 Price Cut 4 Price Cut 6 Price
14 cm. 31.742 $15.55 31.743 $15.55 31.745 $15.55 31.746 $15.55

 

Round Parallel- Cut over the entire surface. 

Cross Section Length Diameter Cut 00 Price Cut 0 Price Cut 2 Price
4" 1/16" . . 31.304 $14.20 31.305 $16.00
4" 1/8" . . 31.307 $16.50 . .
6" 3/32" . . 31.311 $19.20 31.312 $20.99
6" 1/8" . . 31.315 $19.20 31.316 $20.90
6" 5/32" 31.318 $19.00 31.319 $19.95 31.320 $22.00
6" 5/16" 31.321 $19.00 31.322 $19.95 31.323 $21.00
6" ¼" . . . . 31.326 $25.70

 

American Pattern Round, Chain Saw- Used for sharpening all sizes of chain saw teeth, this file maintains the proper tooth shape throughout extensive use.  The chain saw file user will experience a fast, smooth cutting action, creating an excellent finish. Swiss made except 32.282, which is US made.

Cross Section Length Diameter Smooth Cut Price per Dz.
8" 13/64" 32.278S $25.99
8" 3/16" 32.279S $25.99
8" 5/32" 32.280S $25.99
8" 7/32" 32.281S $25.99
8" ¼" 32.282 $41.60

 

 

The I. Shor Co.

I. Shor Canada
Shor International Corporation
Fine Tools, Equipment and Innovative Products Since 1918
20 Parkway West, Mt. Vernon, N.Y. 10552
Phone (914) 667-1100 Fax (914) 667-0190

e-mail:

shorinternational@attglobal.net